Punkbrad
Fri 2/24/06, 6:17PM
DO THIS AT YOU OWN RISK!!!!
Assuming you already put on your blinkers, like i did, and are annoyed by the super-fast cop-attention-getting mad Civic Stylie flashing, you can do this to slow it down....
First go buy this stuff - EL12 HD FLasher ($8.99) & some flat connectors ($3.29) on the shelf at Pep Boys
- Thanks Manny, Moe & Jack for their support on this project -
I bought the insulated kind, so i dont have to tape the shit outta stuff, plus it looks cleaner.
http://img.photobucket.com/albums/v225/punkbradspix/02-27-06_1903.jpg
With some cutters put female flat connectors on like 5 or 6 inches of wire (both sides need not be female)
http://img.photobucket.com/albums/v225/punkbradspix/02-27-06_1915.jpg
Put the females onto the flasher
http://img.photobucket.com/albums/v225/punkbradspix/02-27-06_1916.jpg
Locate the stock flasher (on the right of the box marked FUSE)
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1722.jpg
Pull the Stocker flasher out, its the RIGHT side box
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1723.jpg
Pull the pins from the wire harness (the LIGHT BLUE & the BROWN located on the top row of three wires) in this pic they are already pulled, the voltage meter (pointy tool) is showing you where they were.
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1724.jpg
Once you have those pulled, strip the wires. Now you can also put the stock flasher back in place.
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1725.jpg
Put the corresponding end of flat connector on (the opposite connection of the open end of wires on you flasher )
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1727.jpg
Once you have the connectors on, put the flasher wires on, use tape or a zip tie to keep all the wires close and tight. i used red electrical tape you you can see it here.
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1730.jpg
Secure the flashign Unit in a safe non-vibratory place, I zip-tied it to a hole in the helmet holder part of the seat. you can wrap it in something soft too if you are feeling silly...
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1733.jpg
GOOD LUCK. - YES it will TICK TICK TICK LOUDLY. Its okay. thats normal.
I calim no responsibility if you fuck something up. DO AT YOU OWN RISK. If you are retarded and/or cant use tools, DONT TRY WORKING ON YORU OWN BIKE!!!
Assuming you already put on your blinkers, like i did, and are annoyed by the super-fast cop-attention-getting mad Civic Stylie flashing, you can do this to slow it down....
First go buy this stuff - EL12 HD FLasher ($8.99) & some flat connectors ($3.29) on the shelf at Pep Boys
- Thanks Manny, Moe & Jack for their support on this project -
I bought the insulated kind, so i dont have to tape the shit outta stuff, plus it looks cleaner.
http://img.photobucket.com/albums/v225/punkbradspix/02-27-06_1903.jpg
With some cutters put female flat connectors on like 5 or 6 inches of wire (both sides need not be female)
http://img.photobucket.com/albums/v225/punkbradspix/02-27-06_1915.jpg
Put the females onto the flasher
http://img.photobucket.com/albums/v225/punkbradspix/02-27-06_1916.jpg
Locate the stock flasher (on the right of the box marked FUSE)
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1722.jpg
Pull the Stocker flasher out, its the RIGHT side box
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1723.jpg
Pull the pins from the wire harness (the LIGHT BLUE & the BROWN located on the top row of three wires) in this pic they are already pulled, the voltage meter (pointy tool) is showing you where they were.
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1724.jpg
Once you have those pulled, strip the wires. Now you can also put the stock flasher back in place.
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1725.jpg
Put the corresponding end of flat connector on (the opposite connection of the open end of wires on you flasher )
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1727.jpg
Once you have the connectors on, put the flasher wires on, use tape or a zip tie to keep all the wires close and tight. i used red electrical tape you you can see it here.
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1730.jpg
Secure the flashign Unit in a safe non-vibratory place, I zip-tied it to a hole in the helmet holder part of the seat. you can wrap it in something soft too if you are feeling silly...
http://img.photobucket.com/albums/v225/punkbradspix/02-28-06_1733.jpg
GOOD LUCK. - YES it will TICK TICK TICK LOUDLY. Its okay. thats normal.
I calim no responsibility if you fuck something up. DO AT YOU OWN RISK. If you are retarded and/or cant use tools, DONT TRY WORKING ON YORU OWN BIKE!!!